3D print settings that actually work
Nozzle temp, bed temp, speed and cooling for every filament — with a source behind every entry.
Always test on scrap first. These are starting points from public sources, not guarantees for your exact printer, nozzle or filament batch.
Showing 30 of 30 settings
official
PLA
Bambu Lab H2S · Bambu Lab
Nozzle 190-240 °C (rec…Bed 35-65 °C0.4 mm
Open-frame and enclosed compatible. Bambu generic PLA material table.
See full settings →official
PETG HF
Bambu Lab H2S · Bambu Lab
Nozzle 230-260 °C (rec…Bed 60-80 °C0.4 mm
High-flow PETG. Dry before use. Softened for AMS compatibility.
See full settings →official
ABS
Bambu Lab H2S · Bambu Lab
Nozzle 240-280 °C (rec…Bed 90-100 °C0.4 mm
Requires enclosure / heated chamber. Dry before printing.
See full settings →official
ASA
Bambu Lab H2S · Bambu Lab
Nozzle 240-280 °CBed 90-100 °C0.4 mm
UV-stable alternative to ABS. Enclosure recommended.
See full settings →official
PLA-CF
Bambu Lab H2S · Bambu Lab
Nozzle 210-240 °CBed 35-55 °C0.4 mm harden…
Hardened nozzle required. Carbon fiber filled PLA.
See full settings →official
PETG-CF
Bambu Lab H2S · Bambu Lab
Nozzle 240-270 °CBed 70-90 °C0.4 mm harden…
Hardened nozzle required. Dry thoroughly.
See full settings →official
TPU 95A HF
Bambu Lab H2S · Bambu Lab
Nozzle 200-250 °CBed 30-45 °C0.4 mm
Not for AMS. Direct path preferred. Dry required.
See full settings →official
PA6-CF
Bambu Lab H2S · Bambu Lab
Nozzle 260-290 °CBed 80-100 °C0.4-0.6 mm ha…
Engineering filament. Dry required. Hardened nozzle; 0.6 mm preferred to reduce clog risk.
See full settings →official
PLA
Bambu Lab A1 · Bambu Lab
Nozzle 190-240 °CBed 35-65 °CSpeed <300 mm/s0.4 mm
Open-frame A-series compatible with PLA. Same nozzle range as Bambu guide.
See full settings →official
PETG HF
Bambu Lab A1 · Bambu Lab
Nozzle 230-260 °CBed 60-80 °CSpeed <300 mm/s0.4 mm
Dry first. Open-frame OK for PETG HF; watch chamber heat on enclosed siblings.
See full settings →official
ABS
Bambu Lab A1 · Bambu Lab
Nozzle 240-280 °CBed 90-100 °C0.4 mm
ABS prefers enclosure. A1 is open-frame — expect warping; prefer ASA/PLA-CF for outdoor-ish parts or print sm…
See full settings →official
PLA
Anycubic Kobra 3 Max · Anycubic
Nozzle 190-220 °C (rec…Bed 50-60 °C0.4 mm
Anycubic filament guide PLA range. Level bed; glue stick optional.
See full settings →official
PETG
Anycubic Kobra 3 Max · Anycubic
Nozzle 230-250 °CBed 70-80 °C0.4 mm
Dry PETG. Slightly lower cooling than PLA.
See full settings →official
ABS
Anycubic Kobra 3 Max · Anycubic
Nozzle 240-260 °CBed 90-100 °C0.4 mm
Enclosure strongly recommended. Dry filament.
See full settings →official
TPU
Anycubic Kobra 3 Max · Anycubic
Nozzle 210-230 °CBed 40-60 °CSpeed Slow0.4 mm
Print slowly. Direct drive preferred. Disable or minimize retraction.
See full settings →official
ASA
Anycubic Kobra 3 Max · Anycubic
Nozzle 240-260 °CBed 90-100 °C0.4 mm
Similar to ABS; UV stable. Enclosure recommended.
See full settings →official
PLA Glow
Anycubic Kobra 3 Max · Anycubic
Nozzle 190-220 °CBed 50-60 °C0.4 mm
Glow filament is brittle; ACE Pro feeding may clog — external spool recommended.
See full settings →official
PLA
Creality SPARKX i8 · Creality
Nozzle 190-220 °C (rec…Bed 50-60 °C0.4 mm
Official Creality filament parameter guide. SPARKX i8 uses Creality Print 7+.
See full settings →official
CR-PLA
Creality SPARKX i8 · Creality
Nozzle 190-220 °CBed 50-60 °C0.4 mm
Creality CR-PLA parameters from official filament guide.
See full settings →official
PETG
Creality SPARKX i8 · Creality
Nozzle 230-250 °CBed 70-80 °C0.4 mm
Creality CR-PETG parameters. Direct-extruder table lists retract 60 mm/s / 6 mm.
See full settings →official
ABS
Creality SPARKX i8 · Creality
Nozzle 240-260 °CBed 90-100 °C0.4 mm
Enclosure recommended. Cooling fan off in Creality direct-extruder table.
See full settings →official
TPU
Creality SPARKX i8 · Creality
Nozzle 210-230 °CBed 40-60 °CSpeed Slow0.4 mm
Direct-drive preferred. Slow speeds. Short retraction.
See full settings →official
Silk PLA
Creality SPARKX i8 · Creality
Nozzle 200-220 °CBed 50-60 °C0.4 mm
Creality silk PLA parameters.
See full settings →official
HP-ASA
Creality SPARKX i8 · Creality
Nozzle 240-260 °C (rec…Bed 90-100 °C0.4 mm
Enclosed printer recommended for ASA.
See full settings →official
PLA
Snapmaker U1 · Snapmaker
Nozzle 190-230 °CBed 55-65 °C0.4 mm
Snapmaker U1 printing guide PLA baseline. Use Bambu Studio or Snapmaker profiles.
See full settings →official
PLA + PETG HF support
Snapmaker U1 · Snapmaker / Bambu-compatible
Nozzle PLA 230 °C / PE…Bed 65 °C0.4 mm
PLA model + PETG HF support interface recipe from Snapmaker U1 wiki. Dry PETG. PETG max volumetric ~10 mm³/s.…
See full settings →official
PETG
Snapmaker U1 · Snapmaker
Nozzle 230-250 °CBed 70-80 °C0.4 mm
Dry PETG. Lower cooling than PLA. Follow U1 wiki PETG notes.
See full settings →official
PC
Bambu Lab H2S · Bambu Lab
Nozzle 260-290 °CBed 90-110 °C0.4 mm
Engineering PC. Dry thoroughly. Enclosure required.
See full settings →official
PLA+
Anycubic Kobra 3 Max · Anycubic
Nozzle 200-220 °CBed 50-60 °C0.4 mm
PLA+ often prints a bit hotter than basic PLA per Anycubic guide.
See full settings →official
PLA-CF
Bambu Lab A1 · Bambu Lab
Nozzle 210-240 °CBed 35-55 °C0.4 mm harden…
Hardened nozzle required. Open-frame compatible per Bambu guide.
See full settings →